Need assistance? Call the experts: (727) 223-1816
OR
Sign In
Review
fast service ,easy to install ,it made a gun out of that kimber instead of a paper weight ,i ended up with 5 lb. trigger pull , witch is a lot better than the factory 8 lb. if i shoot it more it might loosen up .thank again.
Went to the range this weekend to try the new spring kit on my Micro 9 and it shot great. I highly recommend it.
Got the kit, was really nice. Got here fast too. However when tried to install, my finger slipped and I lost the trigger spring. Careful all. Anyway, love the product, (what I had left) and the service. Will use these guys again. Thanks
spring kit was easy to install and works great.
I have a Kimber Micro 9 ESV that had a less then desirable 7.5lb trigger pull. After reading the reviews and watching several videos on the M-Cargo spring kit, which includes the Firing Pin Spring, Hammer Spring, and Sear Spring, I ordered and installed the kit. Then I hit the 'road block'. I could not pull the hammer back or push down on the extractor to let the slide in. The sear spring has two fingers; one for the sear and the other for the extractor. The problem was a tiny corner of the extractor finger was hitting the extractor stop pin on the frame; you could almost force past it. I removed the sear spring and measured it. The reading was 2.21". The factory spring measures 2.18". I installed the factory spring everything worked as it should. I contacted M-Carbo, sent them an image of the two springs side by side to show the slight difference, and explained the problem. As a testament to their good customer service M-Carbo wasted no time in sending me 'two' new sear springs to try. Unfortunately the new springs both measured 2.2", still too long, same problem. I then took the longest spring and filed down just the corner of it to 2.18". Life is good again. The trigger pull was reduced from 7.5lbs to 4.8lbs. Spring Kit Item # 2111200055559mm. Thank you M-Carbo for your service. - Felix
THE KIT ARRIVED WITHIN A WEEK. INSTALLATION OF THE SEAR AND EJECTOR TOOK A WHILE TO GET BACK TOGETHER. IF THERE WAS A SLAVE PIN TO PUT IN TO HOLD TOGETHER IN INSTALLATION IT WOULD HAVE WENT FASTER. TRIGGER PULL WAS SUBSTANTIALLY REDUCED AFTER INSTALLATION, PROBABLY 1/2 OR MORE. I ALSO TOOL KIMBER TO RANGE TO MAKE SURE PRIMER INGITION WAS GOOD, WICH IT WAS. 30 RDS FIRES WITH NO PROBLEM. I WOULD RECOMMENT THIS PRODUST TO ALL THOSE THAT HAVE A KIMBER MICO 9 OR 380.
I had a professional gunsmith install the MCarbo spring kit for me and, quite frankly, I can feel no discernible difference in the trigger pull after the installation of this kit.
The parts functioned as promised. Trigger pull was significantly reduced and reliability was not effected. Installation was easy - the video really helped. Getting the sear in place between the trigger bar and the sear spring was very difficult and time-consuming.
The 3 piece kit arrived on Friday, a day earlier than promised. I had it installed minutes later using just a picture hanging nail and paper clip. Watch the updated video and you can do this. The difference from the factory 7 lb trigger is significant. This is the way it should have been delivered. It is not a competition trigger but is noticeably lightened and appropriately secure for carry. The Micro 9 is much more accurate when you can squeeze off steady rounds at the target.
I purchased the Micro 9 new and promptly found the trigger pull to be very very hard. I personally am a fan of spring kits for most of my hand guns. This one did not dissapoint. As advertised it was easy to install and made a nice reduction in trigger pull. This is the second Kit that I have purchased from M CARBO and I have been very satisfied both times. I will continue to use them in the future and reccommend them to my friends.
Went in easy and the video was perfect. Gave it 4 stars because so far it has only reduced the pull by about 13% so far. Might need to break in a little.
i replaced the spring on not one but 2 micro 9. was a little tricky to get it done. but well worth it. my frist thought after i was done with it was wow
replaced spring micro 9 very happy with results video was very helpful great job
I didn't have to file, sand, polish anything to make these springs fit. The went in without a hitch. It did make a lighter break over. But it did not shorten or eliminate the long and spongy trigger creep as I was expecting.
It's been a long time since I've had such good service. The girl who answered the phone was friendly and helpful. I had to wrestle a little bit to do the install but they guided me but they guided me successfully. I felt like part of the team the whole time. I look forward to doing further business with you. Thank you so much, Gregg Ross
The wife wanted the Kimber Micro and I wanted it to have a nice trigger pull for her. This drop in kit is awesome. The instructional video makes this a snap to install. Though I did find that if you install the sear and injector first then put the hammer spring assembly housing back in. Makes this kit just fall into the frame. So in stock form it was right at 6 pounds 4 ounces on a 5 pull average. After installing this kit its is now 3 pounds even on a 5 pull average. Best bang for your buck upgrade for your Kimber Micro 9. My wife loves her new baby, she said the trigger pull is like butter now.